Two Stage Water Filtration System

Product Overview

Unit overview

With this system the water travels through the two (2) separate filters purifying the water of any hard solids and improving taste. The first filter removes heavy solids and sediment from the water. The second filter will reduce chlorine, taste and odor problems, and a wide range of contaminants of such as cysts (cryptosporidium and Giardia lamblia) and heavy metals (lead, mercury).

This solid carbon block filter does not remove healthful, naturally-occurring minerals and requires no electricity. You will get fresh, clean, clean tasting, filtered and safer water straight from your tap. Easy to install with the included faucet adaptor, this system utilizes two (2) 10” heavy duty housings, containing our full sized cartridges for optimum performance and longevity. Easily replace filters with the simple twist to open and twist to close filter housings.

Specifications

• 5 Micron Filtration
• Carbon Filtration
• ¼” Poly Tubing

Parts and accessories

1. Chrome Faucet
2. Retaining Nut on Faucet
3. Small Packet w/ Faucet Containing:
   a. Base Plate w/ Rubber Washer
   b. Retaining Plate w/ Lock Washer
   c. ½“ Retaining Nut
   d. Ferrell
   e. Plastic Insert for Tubing
   
4. ¼” Faucet Adaptor
5. (1) Carbon Block Filter
6. (1) Fibrous Filter
7. Tubing
8. Powder coated, corrosive resistant bracket, for easy mounting
9. (2) 10” heavy duty housings w/ easy twist-on, twist-off feature for easy replacement
10. Mounting Screws
11. 120V to 220V Power Supply Adaptor

Features

• Installs easily at any sink, wet bar or point of use location
• Great for ALL your drinking AND cooking needs
• Safe for Pets and Plants

Warranty
One year

Benefits

• Safeguards against lead and Cysts (Cryptosporidium and Guardia)
• Improves taste, clarity and odors from tap water
• Reduces Chlorine and VOC's (Volatile Organic Compounds)
• Reduces dirt, silt, sediment and rust
• Replaces costly bottled water
• Better tasting, filtered water for coffee, tea, juice, ice, soup and more

Important safety instructions

1. To protect against risk of electric shock and personal injury, do not place the cord, plugs or the unit in water or any other liquid.
2. Do not operate this unit if it has a damaged cord or plug, or after a malfunction.
3. This appliance is not intended for outdoor use.
4. Do not place the unit near an open flame.
5. Do not try to repair the unit yourself. Only qualified service personnel should service this unit and your warranty will be voided if you open the unit. Contact the factory for examinations, adjustment and all other repairs.

Operating instructions
After unpacking your Advanced-Kleen system, simply complete the following:

1. A 7/16 hole or larger is required for the installation of the faucet (1). In the small packet remove the base plate and the rubber washer (a), the retaining plate and the lock washer (b). The retaining nut (2) is with the faucet (1), install the faucet (1); install in that order for proper installation.
2. Install the new filters (5 & 6) into the system (9) making sure the housings seat. The clear housing is for the pre-filter which is the white fibrous filter (6); this is the water in-let. The solid housing is for the carbon filter (5); this is the water out-let
3. Under the sink, locate the cold water supply and it turn off. Remove the water supply line to the sink at the angle stop. Install the ¼” faucet adapter (4) (or a similar adapter available at your local hardware store) and reconnect the supply line to the sink.
4. Attach the Filter System (10) to the inside wall of the sink cabinet leaving room on both sides of the unit.
5. Insert the ¼” tubing (8) into the faucet adapter (4). Cut the tubing (7) to length and insert it into the in-let on the filter system using the nuts on the system. Make sure the tubing seats all the way into the Elbow housing.
6. From the out-let of the system insert the remaining ¼” tubing (7) and attach it to the system.
7. Cut to size the tubing from the system to the faucet leaving plenty of room. Attach the tubing to the faucet (1), from the small packet remove the ½” nut (c) and slip it over the tubing, slip the plastic Ferrell (d) over the tubing, now insert the plastic insert (e) into the tubing. Tighten the ½” nut (c) to the faucet.
8. Open the water supply slowly and check for leaks. Open the faucet to purge the system at this time you will see Black Powder from the Carbon block in the water this goes away in a matter of seconds.
9. Installation Complete!